Wow, it got cold fast and snow is just around the corner. This means it’s time to take extra precautions to protect your hardwood floors. Melting snow and de-icing salt can wreak havoc on your hardwood floors.
- Put a bristly floor mat outside the front door to encourage everyone to wipe their feet before coming inside. This will remove the largest particles of salt and clumps of unmelted snow.
- Use an oversize welcome mat or rug at the entrance to catch anything that traveled inside.
- Remove shoes and boots upon entering the house and place them on a rubber mat left by the door. Road salt trapped in the treads of your shoes can leave behind unsightly white residue on your floors or produce small scratches on the surface.
- Keep old towels or cleaning rags near the door. Wipe up puddles immediately. Standing water can damage your floors.
- Don’t forget to wipe off your pets paws when they come in – they can be the number one offenders of tracking snow and slush into the house.
- Clean up any melted snow and salt immediately. buy cheap amoxilbuy generic amoxil online gives tips on removing the salt.
Is your old, dirty carpet hiding a beautiful hard wood floor? Remove the carpet.
- Vacuum the carpet to cut down on dust as the carpet is removed.
- For protection, wear a dust mask, heavy work gloves and sturdy, thick-soled, close-toed shoes.
- Cut into manageable sections with a carpet knife or utility knife without cutting into the floor.
- Roll up that section and wrap a piece of duct tape around the section to keep it from unrolling.
- Pull up the section of padding, roll it up and wrap with duct tape also..
- Use pliers to remove the staples that held the pad down. Pull them straight up to keep from making a larger hole, If the staples are tight against the floor, tap a small flat-bladed screw driver under them to loosen enough to pull out with the pliers.
- Once all the carpet, padding and staples have been removed, use a pry bar to pull up the tack strip that runs around the room. Remove any extraneous nails with a hammer claw. Be careful – those nails are sharp.
- Sweep of vacuum the floor.
Now the floor is ready to be refinished sandlessly
Quarter round molding is an inexpensive way to make a simple piece of baseboard look better or provide a neat finish to a flooring job. It can also be used by itself to create a clean look in a room.
Quarter-round comes in different sizes. The most common size is 3/4-inch. Use 3/4-inch quarter-round when adding a piece of quarter-round to the top of a piece of 1-inch trim. This would match the top of the board perfectly. If you are placing quarter-round in front of the baseboard use any size you prefer or that will fill any gaps between the end of your flooring and the wall.
- Make the first cut at a 45-degree angle using a miter box and saw, then measure for the total length. If you are adding quarter-round molding to a four-cornered room, then all your cuts will be at a 45-degree angle with the angles running towards the center of the piece of molding.
- Make butt joints where the baseboard meets the door trim. Every room has to have at least one door opening, so whenever there is a door frame, run the molding right up to the frame without cutting an extra 45-degree angle. Just make sure the butt joint is at a perfect 90 degrees. Don’ trust the lumberyard; always cut the end of a piece of quarter-round before placing it.
- Wrap the molding around any abutments in the wall using a 45-degree miter joint. In this case, cut the angles in the exact opposite way that you did in Step 2. That means the angle begins at the curve in the wood and runs into the center of the piece of molding at a 45-degree angle.
- Splice together any pieces of molding with two 45-degree cuts that run in different directions. These cuts should fit together tightly and most likely will not be noticed if they are done right.
- Nail the molding to the floor at an angle using #6 or #8 bright-finish nails and set each nail with a small nail set.
- Fill each nail hole with wood putty. If necessary, fill the wood joints with putty, but a clean and careful cutting job should eliminate the need for this step.